Skip to content

After Landing and Taxi to Gate

This guide will explain the correct procedures after we have landed and vacated the runway, and will also cover taxiing to the designated gate.

Disclaimer

The level of detail in this guide is meant to get a FlyByWire A380X beginner from the runway to the designated destination gate.

A beginner is defined as someone familiar with flying a GA aircraft or different types of airliners. Aviation terminology and know-how is a requirement to fly any airliner, even in Microsoft Flight Simulator.

Further reading: A320 Autoflight

TODO: update/this link for 380

Prerequisites

Aircraft has vacated the runway completely and has been brought to a stop on the taxiway as per previous chapters.

Runway vacated

TODO: update/screenshot

Download FlyByWire Checklist

Chapters / Phases

This guide will cover these phases:

  1. After Landing
  2. Taxi to Gate

1. After Landing

Situation:

  • Aircraft has vacated the runways completely and has come to a stop on the taxi way as per previous chapters.
  • Flaps and Ground Spoilers are still deployed.
  • ATC has been informed that we vacated the runway.

Simulation vs. Real Life

In real life, the A380 will have two pilots who can actually do things in parallel. Talking to ATC, taxiing the aircraft and doing the after landing tasks.

In the simulation we are typically alone, so it is perfectly fine to stop once we have fully vacated the runway and do these things one after the other.

ATC Tower will usually hand us off to ATC Ground, and they will give us taxi instructions for our destination gate. Write them down and read them back as usual, but you don't have to move immediately unless ATC explicitly tells you to. Online ATC understand that the after-landing- tasks do take some time.

Immediate steps after vacating the runway:

  • Set your radio frequency to the one assigned by ATC or the airport charts.

    EDDM ATC frequencies

    RMP Panel

    TODO: update/screenshot

  • Disarm the Speed Brake lever (Ground Spoilers) by pushing down on the lever.

    Spoiler armed and disarmed

    TODO: update/screenshot

GROUND SPOILERS ...................................................... OFF

  • Set your ENG MODE selector to NORM in case you set it to IGN/START before.

    Engine Mode Switch Norm

    TODO: update/screenshot

ENGINE START SELECTOR ......................................... CHECK NORM

  • Retract your FLAPS to 0.

    Flaps 0

    TODO: update/screenshot

FLAPS ........................................................... RETRACT

  • Set your TCAS to STANDBY.

TCAS ............................................................. STANDBY

ATC & TCAS

TODO: update/screenshot

  • Set your RADAR and Predictive Windshear System (PWS) to OFF.

WEATHER RADAR ........................................................ OFF
PREDICTIVE WINDSHEAR SYSTEM .......................................... OFF

WX and PWS off

TODO: update/screenshot

  • Start your APU by clicking the APU MASTER SW button, then the APU START button.

APU Start

TODO: update/screenshot

AUXILLIARY POWER UNIT START ........................................... ON

  • Turn ANTI ICE OFF if not required.

    TODO: update/screenshot

ANTI-ICE ..................................................... AS REQUIRED

  • Set your exterior lights:

LANDING LIGHTS ....................................................... OFF
STROBE .............................................................. AUTO
OTHER EXTERIOR LIGHTS ........................................ AS REQUIRED
NOSE ................................................................ TAXI
RUNWAY TURN OFF LIGHTS ....................................... AS REQUIRED

After landing lights

TODO: update/screenshot

  • Turn the brake fan (BRK FAN) on if you get a hot brakes ECAM warning.

BRAKE TEMPERATURE ................................................ MONITOR
BRAKE FAN .................................................... AS REQUIRED

Hot Brakes Brake Fan on

TODO: update/screenshot

  • Complete the After Landing checklist.

    After Landing Checklist

This concludes After Landing

2. Taxi to Gate

Situation:

  • Aircraft on taxiway directly after runway.
  • After Landing checklist is completed.
  • ATC Ground has given taxi instructions.

Taxiing

Make sure to also read the Taxi section of the Engine Start and Taxi chapter.

Use your charts to follow the ATC taxi instructions to the designated gate.

Crossing a Runway

When approved to cross a runway (active or not) perform the following actions:

  • Look out the windows and visually ensure that there are no visible aircraft to your left and right.
  • Turn on extra lights to ensure your aircraft is visible when crossing:
    • Strobe lights - Set to ON
  • Inform ATC you have vacated the runway if required.

Warning

NEVER cross a runway without express permission from ATC and providing a read back of said instructions. Always ensure maximum safety when crossing.

ATC CLEARANCE ..................................................... OBTAIN
STROBE LIGHTS ......................................................... ON

After you have crossed the runway and are on the adjacent taxiway, turn the strobe lights back off, and notify ATC you are clear of that runway.

STROBE LIGHTS ........................................................ OFF

Turning into the Gate

When turning into the gate, turn off your NOSE light and your RWY TURN OFF lights to not blind the ground personnel. This of course is only done if enough lighting is available to safely navigate and park into the gate.

Taxi lights off

TODO: update/screenshot

This concludes Taxi to Gate

Continue with Powering Down